Standard
[WITHDRAWN]
ISO 19085-12:2021-03
Woodworking machines - Safety - Part 12: Tenoning/profiling machines
German title
Holzbearbeitungsmaschinen - Sicherheit - Teil 12: Zapfenschneid- und Schlitzmaschinen/Profiliermaschinen
Publication date
2021-03
Original language
English
Pages
53
Publication date
2021-03
Original language
English
Pages
53
Product information on this site:
Quick delivery via download or delivery service
Buy securely with a credit card or pay upon receipt of invoice
All transactions are encrypted
Content
Content (en)
Foreword
Introduction
Scope
Normative references
Terms and definitions
List of significant hazards
Safety requirements and measures for controls
Show subsection Close subsection Safety and reliability of control systems
Control devices
Show subsection Close subsection General
Additional requirements for single end tenoning machines with manual feed sliding table
Additional requirements for single end tenoning machines with mechanical feed sliding table
Additional requirements for single end tenoning and/or profiling machines with mechanical feed
Additional requirements for double end machines
Additional requirements for angular systems for tenoning and profiling with mechanical feed
Start
Show subsection Close subsection Machines with manual feed
Machines with mechanical feed
Laser marking unit
Safe stops
Show subsection Close subsection General
Normal stop
Operational stop
Emergency stop
Braking function of tool spindles
Mode selection
Show subsection Close subsection General
Adjustment mode (MODE 2)
Spindle speed changing
Show subsection Close subsection Spindle speed changing by changing belts on the pulleys
Spindle speed changing by incremental speed change motor
Infinitely variable speed by frequency inverter
Failure of any power supply
Manual reset control
Enabling control
Machine moving parts limited speed monitoring
Time delay
Tele-service
Safety requirements and measures for protection against mechanical hazards
Show subsection Close subsection Stability
Show subsection Close subsection Stationary machines
Displaceable machines
Risk of break-up during operation
Tool holder and tool design
Show subsection Close subsection General
Spindle locking
Circular saw blade fixing devices
Flange dimensions for circular saw blades
Spindle rings
Braking
Show subsection Close subsection Braking of tool spindle
Maximum run-down time
Brake release
Safeguards
Show subsection Close subsection Fixed guards
Interlocking moveable guards
Show subsection Close subsection General
Moveable guards with interlocking without guard locking
Moveable guards with interlocking and guard locking
Hold-to-run control
Two hand control
Electro-sensitive protective equipment (ESPE)
Pressure sensitive protective equipment (PSPE)
Prevention of access to moving parts
Show subsection Close subsection General
Guarding of tools
Show subsection Close subsection Single end tenoning machines with manual feed sliding table
Single end tenoning machines with mechanical feed sliding table
Single end tenoning and/or profiling machines with mechanical feed
Show subsection Close subsection General
Measures against access to hazard points through the opening between lower work-piece support and upper feeder rollers
Measures against access to hazard points through the opening between feed chain and top pressure beam
Double end tenoning and/or profiling machines with mechanical feed
Show subsection Close subsection General
Guarding of sanding belts
Guarding of units installed out of the integral enclosure
Access between machine halves
Angular systems for tenoning and profiling with mechanical feed
Guarding of drives
Guarding of shearing and/or crushing zones
Show subsection Close subsection Guarding of the chain or feed mechanisms
Show subsection Close subsection General
Infeed end of the machine
Outfeed end of the machine
Safeguarding of machine half movement on double end machines
Show subsection Close subsection Crushing between machine halves during closing movement
Crushing between machine halves and fixed parts of the machine during opening movement
Safeguarding of sliding table in angular systems for tenoning and profiling with mechanical feed
Impact hazard
Clamping devices
Show subsection Close subsection Single end tenoning machines with sliding table
Machines other than single end tenoning machines with sliding table
Measures against ejection
Show subsection Close subsection General
Guards materials and characteristics
Show subsection Close subsection Choice of class of guards
Guards of class A
Guards of class B
Devices to minimize the possibility or effect of ejection or kickback
Work-piece support and guides
Show subsection Close subsection Single end tenoning machines with sliding table
Single end tenoning and/or profiling machines with mechanical feed
Double end tenoning and/or profiling machines with mechanical feed
Angular systems for tenoning and profiling with mechanical feed
Work-piece returner
Safety requirements and measures for protection against other hazards
Show subsection Close subsection Fire
Noise
Show subsection Close subsection Noise reduction at the design stage
Noise emission measurement
Emission of chips and dust
Electricity
Show subsection Close subsection General
Displaceable machines
Ergonomics and handling
Lighting
Pneumatics
Hydraulics
Electromagnetic compatibility
Laser
Static electricity
Errors of fitting
Isolation
Maintenance
Heat
Substances
Information for use
Show subsection Close subsection Warning devices
Marking
Show subsection Close subsection General
Additional markings
Instruction handbook
Show subsection Close subsection General
Additional information
Performance levels required (informative)
Tests for braking function (normative)
Stability test for displaceable machines (normative)
Impact test for guards (normative)
Noise emission measurement for single end profiling machines (not in ) (normative)
Show subsection Close subsection General
Noise measurements
Show subsection Close subsection Test conditions
Microphone positions
Show subsection Close subsection Operator's positions
Other microphone positions
General data sheet
Bibliography
Cooperation at DIN
Please get in touch with the relevant contact person at DIN if you have problems understanding the content of the standard or need advice on how to apply it.
Loading recommended items...
Loading recommended items...
Loading recommended items...